Main Site
FTP Site
What's New?
Contact Info

Home
Drivers & Utils
BIOS
Troubleshoot
FAQs
Other Links

PREMIO Value Series (201A) FAQ
PREMIO Value Series (201A) FAQ and BIOS History

Which section do you wish to go to?

  • BIOS Questions
  • Hardware Questions
  • Operating System Specific Questions
  • BIOS History
  • ALi M15xx UltraDMA/33 busmastering drivers for all operating systems 188K (extract with -D)

    BIOS Questions
    Do you have a BIOS history file that includes the problem(s) fixed for each revision of the BIOS?

  • Yes, click here for the file.

    How do I clear the CMOS? How do I clear the BIOS password?

  • Power off your system, move JBAT (located next to the BIOS chip) to 2-3 and leave it there for 2 or 3 seconds.
  • Move JBAT back to 1-2 and power up your system.

    I'm running Windows 95 and plug & play doesn't seem to work.

  • Go into the BIOS's PCI/PnP Configuration and enable the PnP OS option.

    I flashed my BIOS, but now I get no video.

  • Try clearing your CMOS (see above).

    How come the options I see in the BIOS doesn't always match the ones in the manual?

  • Because BIOS are updated constantly, the manual cannot always keep up with the changes.

    Back to top...

    Hardware Questions
    I've turned the system on, but I'm getting no power (i.e., power supply fan does not even spin).

  • If your ATX power supply has an on/off button in the back, make sure it's turned on.
  • Make sure the wire from your power switch is connected properly to the motherboard; see the motherboard manual.
  • Try reseating the ATX power connector to the motherboard.
  • Disconnect all power connectors to your HDD, FDD, CD-ROM, etc. then try to turn the system on.

    Can I mix DIMMs and SIMMs?

  • It is not recommended to mix DIMMs and SIMMs. DIMMs are usually 3.3V while SIMMs are 5.0V.
  • This motherboard only takes unbuffered 3.3V DIMMs.

    How do I enable UltraDMA/33?

  • Make sure your HDD is UltraDMA/33 compliant.
  • Download the ALI M15xx UltraDMA/33 drivers 188K (extract with -D).

    Can I use just one (1) DIMM?

  • Yes, the system board will work with just one DIMM present. For SIMMs, you will still have to use a pair.

    How do I get a plug and play card to work in DOS and/or Windows 3.11/WfW?

  • You need to run the ICU (ISA Configuration Utility) that shipped with the card.

    I have a PnP soundcard and PnP modem, but I'm getting conflicts.

  • It's recommended that you let the modem take COM2 (2F8h/IRQ3); see the question below.
  • And set the soundcard at 220h/IRQ5/DMA1, if possible.
  • Also, try adding the card in one at all time; put the soundcard in first, let 95 detect it, then add the modem.

    I have a plug and play modem, how do I setup it for COM2 in Windows 95?

  • Disable serial port 2 in the BIOS and remove the COM2 port, if present, in Windows 95's Device Manager.

    I get no video; how do I troubleshoot it?

  • Try reseating your video cards, memory, and CPU; or try swapping out the components.

    Back to top...

    Operating System Specific Questions
    Do you have a troubleshooting guide for Windows 95?

  • Yes, we do; please see PREMIO PC Windows 95 Troubleshooting Guide.

    I cannot down a shutdown in Windows 98.

  • If your BIOS is version 4.1 or lower, then you need to disable the USB controller in the BIOS first.

    I'm running DOS/Windows 3.11/WfW; how do I use plug and play cards?

  • You need to run the ICU (ISA Configuration Utility) that came with the PnP cards.

    I'm running Windows NT 3.51 and I've applied service pack 4, now I can't see my IDE CD-ROM drive.

  • If your CD-ROM is on the secondary IDE channel, make sure it's set to master, not slave.

    I'm using Novell Netware 3.x/4.x; how do I get Novell to mount IDE CD-ROM drives?

  • You need to get the HAM drivers.

    I have more than 16MB of memory, but Netware only shows 16MB.

  • Consult your Netware manual; you may need to register your memory.

    Back to top...

    Award BIOS History
    Version 4.1 (released 05/21/1998)

  • Fixed the problem of Cyrix 83.3Mhz CPU in which it will hang in Windows 95.
  • Fixed the problem of boot sequence.
  • Added support for SDMS 3.0.
  • Added typematic keyboard support function.

    Version 3.0

  • The default value for Pipelined Function is changed to Disabled for better compatibility with DVD ROM.
  • The default value for DRAM Refresh Period is changed to 15us to solve compatiblity problems with Mitsubishi memory.
  • The default value for Primary Frame Buffer is changed to Disabled and VGA Frame Buffer is changed to Disabled to solve the problem of screen corruption when running Netware 3.12 using Cyrix CPU.
  • When Power Button is set to Disabled: in Windows 95 DOS mode, if the power switch is pressed once, and EXIT is typed to run Windows 95, the system will power off.
  • Fixed: the date and time will be cleared, after the system is powered off for a period of time.

    Version 2.0

  • Fixed some plug and play issues with Windows 95.

    Version 1.0

  • Initial BIOS release.

    Back to top...

    Back to BIOS Page...